Electric Heating Hot Water X-L PIPE

OVER VIEW

It is an innovative heating system that uses heat and increased pressure generated by Heat Transfer Medium by heating the sealed X-L PIPE without boiler in which water or other fluid is heated and water circulation motor which pumps water circulated in the PIPE.

Heated electric wires in X-L pipe collect vapors in the upper part of X-L pipe, resulting in internal pressure and unclear boiling when temperature difference between liquid and gas is over 10℃. As a result, internal pressure will be the negative pressure which is lower than atmospheric pressure at room temperature and so, boiling temperature of water will get lower. The temperature of floor will be increased and heat will last longer according to Nucleate Boiling phenomenon. Therefore, this process increases energy efficiency and you can save energy by using this energy saving product. One of the products using this technology is a pressure cooker.

It is the innovative high energy efficient floor heating system that has no heat loss and achieves 30℃ rise effect in temperature. Our patented pressure absorbing device absorbs too much internal pressure and also the heat transfer medium and carbon tissue absorb the electromagnetic waves for well-being life.

Nucleate Boiling phenomenon : The process of forming steam bubbles within liquid in micro cavities adjacent to the wall if the wall temperature at the heat transfer surface rises above the saturation temperature while the bulk of the liquid is subcooled. The bubbles grow until they reach some critical size, at which point they separate from the wall and are carried into the main fluid stream.

5 CONDITION OF ELECTRIC X-L PIPE HEATING SYSTEM

1. Pressure absorbing device : It absorbs the internal pressure caused the Nucleate Boiling.
2. Double Coated Electric Wires : Since the conductor and the electric wire processing affect on product
    life and its function, make sure to read the followings.
    - Conductor : 7 Strained Nickel
    - Chrome Coil
    - The First Coating : Silicon Rubber coating that can stand very high temperature(280℃) and has excellent       insulating quality,
    - The Second Coating : Heat resistant Teflon rubber coating that is water resistant and chemical resistant.
3. Heat Conducing Medium : They should not freeze at twenty degrees below zero.
4. Harmless to Human Body : Electromagnetic waves are absorbed by itself.
5. Cable : Should not exceed 20W/m.(According to Clause 5, Article 225 of Electric Installation Regulations.
    "The temperature of Electric wires should not exceed 80℃" and/or "Internal Temperature of X-L should not
    exceed 80℃")

Electric Hot water X-L PIPE Heating System

Nucleate Boiling phenomenon : The process of forming steam bubbles within liquid in micro cavities adjacent to the wall if the wall temperature at the heat transfer surface rises above the saturation temperature while the bulk of the liquid is subcooled. The bubbles grow until they reach some critical size, at which point they separate from the wall and are carried into the main fluid stream.

ELECTRIC HOT WATER TUBE PRESSURE TEST

Temperature(℃)	Non Inclusion Wave absorber (Others)	Inclusion wave absorber (ENERPIA)	Unit
30	0.05	0.0	Kgf/㎡
40	0.2	0.1	Kgf/㎡
50	0.4	0.2	Kgf/㎡
60	0.65	0.3	Kgf/㎡
70	0.9	0.4	Kgf/㎡
80	Damage	0.68	Kgf/㎡

BENEFITS OF ELECTRIC X-L PIPE HEATING SYSTEM

1.ECONOMY

Electric Energy is converted to thermal energy at 100% efficiency and used for heating.

Heat is accumulated in the liquid filled in the tube and covering cement (or less) mortar and supplies heat for
a long time.

Average power consumption rate is approx 75 W/h. Minimum energy and maintenance cost.

Less than 70% cheaper than compare with the Oil price by nuclear boiling effect
2. SIMPLICITY

Efficient space usability no boiler room required maintenance work can be conducted through check box - no
need to excavate the floor.

Existing Floor heating tube can be converted by adding electric heating wire.
3. SAFETY

Consists of 1 - line return circuit, liquid heat medium the mortar concerning only - no electromagnetic wave is
generated. 100% is safety for human health. Specific induction ratio of water : 81, Magnetic 5~6

Conductor heat media are double-sealed to prevent leakage and explosion. (Utility Model No. 0442474)

Tube expansion by heat is absorbed patented device to prevent liquid leakage or damage of the X-L PIPE
(Patent no. 0805702)
4. DURABILITY

Externally installed Cold Lead and excess pressure installation release system prevents in the tube from failure.

Semi- Permanent System - No displacement of the system after installation

Simple structure enables easy service and maintenance. A natural substance in the tube prevents heat
accumulation and freezing(-20℃)
5. FUNCTIONALITY

The heating system is likely ONDOL which is traditional system. It is heat radiation and negative ion, provide
pleasant room atmosphere.

Possible to heat for just sectional heat as well as total heating for the floor.

Hot water tube radiant plenty of far infrared rays and negative ions which are good for health.
( Far IR : 0.891, Negative ion : 142)
6. VARIOUS WAY

Applicable to Accommodations, Schools, Vacation facilities

Applicable to Hospital, Post-Delivery care center, Church

Applicable to Restaurant, Green House, Swimming Pool Factory

SPECIFICATIONS OF ELETRIC X-L PIPE HEATING SYSTEM

Model	Dimensions	Power Input	Caloric Value	Heating Capacity	Power Consumption(avr.)
EP-010	14m x 15Φ	20~40W/m	1032Kcal/h	3.3㎡	170Wh/㎡
EP-015	21m x 15Φ		1548Kcal/h	4.95㎡
EP-020	28m x 15Φ		2064Kcal/h	6.6㎡
EP-025	35m x 15Φ		2580Kcal/h	8.25㎡
EP-030	42m x 15Φ		3096Kcal/h	9.9㎡
EP-040	56m x 15Φ		4128Kcal/h	13.2㎡